摘要：本应用笔记介绍MAX5581 DAC与PIC®微控制器的配合使用，给出了详细的电路图和源代码。 MAX5581简介 MAX5581是一款12位、快速建立DAC，采用3线SPI™串行接口。MAX5581的接口支持高达20MHz的SPI，最快建立时间为3µs。本应用笔记给出了连接高速PIC微控制器(PIC18F核)和MAX5581 DAC的应用电路以及所需要的全部固件。汇编程序利用MPLAB IDE、6.10.0.0版本中免费提供的编译器编写，用于PIC18F442。 硬件说明 这里讨论的应用电路采用了MAX5581评估板，包括：MAX5581、超高精度电压基准(MAX6126)、两个按键开关、增益设置电阻和PCB。PIC18F442没有安装在MAX5581EVKIT板上，但已添加到系统中，图1所示是一个完整的应用电路。MAX5581EVKIT上的/CS、SCLK、DIN和DOUT焊盘便于SPI串行接口的连接。 查看大图 图1. MAX5581应用电路第一部分 图1. MAX5581应用电路第二部分 模拟与数字地平面 将模拟地与数字地分离开(如图2所示)可以得到较好的实际效果，利用铁氧体磁珠，如TDK MMZ1608B601C，连接两个地平面。这种布局可以避免微控制器系统时钟及其谐波成份馈入模拟地。已知PIC18F442的系统时钟为40MHz，考虑到MMZ1608B601C特殊的阻抗与频率特性，我们选择了这款铁氧体磁珠。图3给出了MMZ1608B601C阻抗随频率的变化曲线。 图2. 分离的模拟地和数字地 图3. TDK MMZ1608B601C铁氧体磁珠阻抗随频率的变化曲线 固件说明 列表1给出的汇编程序通过PIC18F442的内部MSSP SPI接口对MAX5581进行初始化，PIC18F442的40MHz系统时钟允许MSSP提供高达10MHz的SPI时钟(SCLK)。表1所示为上电后的配置字。一旦完成了对MAX5581的初始化，程序便将DAC输出寄存器装载为零，然后装载满量程输出，如表2所示。该固定循环程序可产生方波输出，如图4所示，可以用来演示MAX5581的快速建立时间。 图4. 一个输出为80kHz方波的实际示波器测试图 列表1. 用于连接MAX5581和PIC18F442内部MSSP SPI接口的汇编程序 下载: P18F442.INC 列表1.asm ;****************************************************************************** ; ; Filename:Listing 1 (Absolute Code Version) ; Date: 2/25/05 ; File Version: 1.0 ; ; Author: Ted Salazar ; Company: Maxim ; ;****************************************************************************** ; ;Program Description: ; ;This program interfaces the internal SPI MSSP ;(Peripheral) of the PIC18F442 to the MAX5581 SPI ;Quad DAC. The program initializes the MAX5581 ;and dynamically generates a 50% duty cycle square ;wave with a frequency of 80KHz. ; ; ;****************************************************************************** ; ; History: ; 2/25/05: Tested SPI DAC format ; 2/25/05: Initialized MAX5591 ; 12/14/04: Cleared tcount timer in HWSPI_W_spidata_W ;****************************************************************************** ;****************************************************************************** ; ;****************************************************************************** ; ; Files required: P18F442.INC ; ;****************************************************************************** radix hex ;Default to HEX LIST P=18F442, F=INHX32;Directive to define processor and file format #include ;Microchip's Include File ;****************************************************************************** ;****************************************************************************** xmit equ06 ; Asynchronous TX is at C6 ; ;****************************************************************************** ;Configuration bits ; The __CONFIG directive defines configuration data within the .ASM file. ; The labels following the directive are defined in the P18F442.INC file. ; The PIC18FXX2 Data Sheet explains the functions of the configuration bits. ; Change the following lines to suit your application. ;T__CONFIG_CONFIG1H, _OSCS_OFF_1H & _RCIO_OSC_1H ;T__CONFIG_CONFIG2L, _BOR_ON_2L & _BORV_20_2L & _PWRT_OFF_2L ;T__CONFIG_CONFIG2H, _WDT_ON_2H & _WDTPS_128_2H ;T__CONFIG_CONFIG3H, _CCP2MX_ON_3H ;T__CONFIG_CONFIG4L, _STVR_ON_4L & _LVP_OFF_4L & _DEBUG_OFF_4L ;T__CONFIG_CONFIG5L, _CP0_OFF_5L & _CP1_OFF_5L & _CP2_OFF_5L & _CP3_OFF_5L ;T__CONFIG_CONFIG5H, _CPB_ON_5H & _CPD_OFF_5H ;T__CONFIG_CONFIG6L, _WRT0_OFF_6L & _WRT1_OFF_6L & _WRT2_OFF_6L & _WRT3_OFF_6L ;T__CONFIG_CONFIG6H, _WRTC_OFF_6H & _WRTB_OFF_6H & _WRTD_OFF_6H ;T__CONFIG_CONFIG7L, _EBTR0_OFF_7L & _EBTR1_OFF_7L & _EBTR2_OFF_7L & _EBTR3_OFF_7L ;T__CONFIG_CONFIG7H, _EBTRB_OFF_7H ;****************************************************************************** ;Variable definitions ; These variables are only needed if low priority interrupts are used. ; More variables may be needed to store other special function registers used ; in the interrupt routines. CBLOCK0x080 WREG_TEMP;variable used for context saving STATUS_TEMP;variable used for context saving BSR_TEMP;variable used for context saving ; ENDC CBLOCK0x000 EXAMPLE;example of a variable in access RAM ; temp ; temp2 ; xmtreg ; cntrb ; cntra ; bitctr ; tcount; speedLbyte;T Being used in HWSPI_speed ; ENDC ;****************************************************************************** ;Reset vector ; This code will start executing when a reset occurs. ORG0x0000 gotoMain;go to start of main code ;****************************************************************************** ;High priority interrupt vector ; This code will start executing when a high priority interrupt occurs or ; when any interrupt occurs if interrupt priorities are not enabled. ORG0x0008 braHighInt;go to high priority interrupt routine ;****************************************************************************** ;Low priority interrupt vector and routine ; This code will start executing when a low priority interrupt occurs. ; This code can be removed if low priority interrupts are not used. ORG0x0018 movffSTATUS,STATUS_TEMP;save STATUS register movffWREG,WREG_TEMP;save working register movffBSR,BSR_TEMP;save BSR register ;*** low priority interrupt code goes here *** movffBSR_TEMP,BSR;restore BSR register movffWREG_TEMP,WREG;restore working register movffSTATUS_TEMP,STATUS;restore STATUS register retfie ;****************************************************************************** ;High priority interrupt routine ; The high priority interrupt code is placed here to avoid conflicting with ; the low priority interrupt vector. HighInt: ;*** high priority interrupt code goes here *** retfieFAST ;****************************************************************************** ;Start of main program ; The main program code is placed here. Main: ;*** main code goes here *** start ;*** Port Initialization *** movlw0x0FF movwfPORTB clrfPORTA movlw0x06 ;T Configure PortA as Digital movwf ADCON1 movlw 0x00FB ;T A2 OUTPUT, ALL OTHERS INPUT movwf TRISA movlw0x0001 ;T B0 INPUT, ALL OTHERS OUTPUT movwfTRISB movlw0x0093 ;T C7-C0 => bit7-0 ;T OUTPUTs: C6(TX), C5(MOSI), C3(SCLK), C2(CS) ;T INPUTs:C4 (MISO) and all others movwfTRISC ;T TRISC bit3 Master = 0 bsfPORTC,RC2;T RC2 = CS\ Make CS\ high ; *** SPI Initialization *** callHWSPI_init ;T Initialize the MSSP for SPI ; *** SPI Configuration *** movlwb'00000000' ;T load W with test byte for CPOLCPHA 0,0 ;T b'00000000' => CPOLCPHA 0,0 ;T b'00000001' => CPOLCPHA 0,1 ;T b'00000010' => CPOLCPHA 1,0 ;T b'00000011' => CPOLCPHA 1,1 callHWSPI_W_configure ; *** SPI Speed *** movlwb'00000000' ;T load W with test byte for SPI Freq ;T b'00000000' => Fosc/4 = 10MHz ;T b'00000001' => Fosc/16 = 2.5Mhz ;T b'00000010' => Fosc/64 = 625kHz ;T b'00000011' => Reserved. call HWSPI_W_speed ;****************************************************************************** ; *** MAX5581 Initialization *** bcfPORTC,RC2;T RC2 = CS\ Make CS\ Low movlw0xEC;T byte0 of settling time config callHWSPI_W_spidata_W;T HW SPI WriteRead Operation movlw0x0F;T byte1 of settling time config callHWSPI_W_spidata_W;T HW SPI WriteRead Operation bsfPORTC,RC2;T RC2 = CS\ Make CS\ high ; *** MAX5581 Load All DAC Outputs to Zero Scale *** Loopforever bcfPORTC,RC2;T RC2 = CS\ Make CS\ Low movlw0xD0;T byte0 of load all input/output to zeros callHWSPI_W_spidata_W;T HW SPI WriteRead Operation movlw0x00;T byte1 of load all input/output to zeros callHWSPI_W_spidata_W;T HW SPI WriteRead Operation bsfPORTC,RC2;T RC2 = CS\ Make CS\ high ; *** MAX5581 Load All DAC Outputs to Full Scale *** bcfPORTC,RC2;T RC2 = CS\ Make CS\ Low movlw0xDF;T byte0 of load all input/output to zeros callHWSPI_W_spidata_W;T HW SPI WriteRead Operation movlw0xFF;T byte1 of load all input/output to zeros callHWSPI_W_spidata_W;T HW SPI WriteRead Operation bsfPORTC,RC2;T RC2 = CS\ Make CS\ high ; movwf xmtreg;T move w to xmtreg ; call asyxmtc;T call UART routine ; gotoLoopforever ;T loop forever ;****************************************************************************** errsrv movlw0x65; load w with 'e' = 0x65 movwfxmtreg ; move w to xmtreg callasyxmtc; call UART routine dead goto dead ; goto endless loop ;****************************************************************************** set_cf_error movlw 0x00 ; 0x00 into W sublw 0x00 ; Subtract W-0x00: If W<=N C set; If W>N C clear. return ; error=> cf=set ;****************************************************************************** clear_cf_ok movlw 0x01 ; 0x00 into W sublw 0x00 ; Subtract W-0x00: If W<=N C set; If W>N C clear. return ; success=> cf=clear ;****************************************************************************** HWSPI_init;T SPI MSSP Initialization for M2EAM schematic ;T CPOL,CPHA = 0,0 => CKP = 0 & CKE = 1 bcfSSPCON1,SSPEN;T Disable the MSSP, SSPCON-5 ; bcfTRISC,SDO;T TRISC bit5 RC5/SDO = 0 MOSI Output bcfTRISC,SCK;T TRISC bit3 RC3/SCK = 0 SCLK Output bsfTRISC,SDI;T TRISC bit4 RC4/SDI = 1 MISO Input movlw 0x0040 ;T SSPSTAT bit8 = 0 sampled in middle ;T SSPSTAT bit6 = CKE = 1 movwf SSPSTAT ;T Used to be sspstat on older PICs movlw 0x0020;T SSPCON1 bit5 SSPEN = 1 Enables sycn serial port ;T SSPCON1 bit4 = CKP = 0 ;T SSPCON1 bit3= 0 = Turn MSSP ON for SPI ;T SSPCON1 bit2-0 = 000b = SCLK = Fosc/4 ;T SSPCON1 bit2 = 0 = Master movwf SSPCON1 ;T Used to be sspcon on older PICs bsfINTCON,PEIE;T INTCON bit6 = PEIE = 1 = Enable periph interrupt bsfPIE1,SSPIE ;T PIE1 bit3 = SSPIE = 1 = interrupt enable movlw0x00;T load 0x00 into W movwftcount;T initialize tcount to zero (0x00) ;****************************************************************************** HWSPI_W_configure ;Configure SPI Mode ; ;On Entry:WREG = confDATA ;On Exit: ;On Success: return with C flag clear ;On Failure: return with C flag set ; bcfSSPCON1,SSPEN;T Disable the MSSP, SSPCON1-5 movwftemp ;T move the confDATA byte to temp btfscSSPCON1,SSPM3 ;T In SPI Mode?, skip if yes call HWSPI_init;T MSSP is in wrong mode, Init for SPI ; btfsctemp,1;T Is bit1 of confDATA byte clear? if so skip next goto CPOL_1;T goto CPOL = 1 label => CPOL = 1 btfsctemp,0;T Is bit0 of confDATA byte clear? if so skip next ;T => CPOL = 0 , CPHA = ? goto CPOLCPHA_01;T goto => CPOL = 0 CPHA = 1 ;Configure for CPOL = 0, CPHA = 0 bcfSSPCON1,CKP;T SSPCON1 bit4 = CKP = 0 bsfSSPSTAT,CKE;T SSPSTAT bit6 = CKE = 1 btfsc SSPCON1,CKP;T Is SSPCON1 bit4 = CKP = 0 ? gotobadjump;T CKP bit test error btfssSSPSTAT,CKE;T Is SSPSTAT bit6 = CKE = 1 ? gotobadjump;T CKE bit test error goto okjump2;OK configured! ; CPOL_1btfsctemp,0;T Is bit0 of confDATA byte clear? if so skip next ;T CPOL = 1 , CPHA = ? gotoCPOLCPHA_11;T goto => CPOL = 1, CPHA = 1 ;Configure for CPOL = 1, CPHA = 0 bsfSSPCON1,CKP;T SSPCON1 bit4 = CKP = 1 bsfSSPSTAT,CKE;T SSPSTAT bit6 = CKE = 1 btfss SSPCON1,CKP;T Is SSPCON1 bit4 = CKP = 1 ? gotobadjump;T CKP bit test error btfssSSPSTAT,CKE;T Is SSPSTAT bit6 = CKE = 1 ? gotobadjump;T CKE bit test error goto okjump2;OK configured! ; CPOLCPHA_01 ;configure for CPOL = 0, CPHA = 1 bcfSSPCON1,CKP;T SSPCON1 bit4 = CKP = 0 bcfSSPSTAT,CKE;T SSPSTAT bit6 = CKE = 0 btfsc SSPCON1,CKP;T Is SSPCON1 bit4 = CKP = 0 ? gotobadjump;T CKP bit test error btfscSSPSTAT,CKE;T Is SSPSTAT bit6 = CKE = 0 ? gotobadjump;T CKE bit test error goto okjump2;OK configured! ; CPOLCPHA_11 ;configure for CPOL = 1, CPHA = 1 bsfSSPCON1,CKP;T SSPCON1 bit4 = CKP = 1 bcfSSPSTAT,CKE;T SSPSTAT bit6 = CKE = 0 btfss SSPCON1,CKP;T Is SSPCON1 bit4 = CKP = 1 ? gotobadjump;T CKP bit test error btfscSSPSTAT,CKE;T Is SSPSTAT bit6 = CKE = 0 ? gotobadjump;T CKE bit test error goto okjump2;OK configured! ; okjump2bsfSSPCON1,SSPEN;T Re-enable MSSP gotoclear_cf_ok return badjumpbsfSSPCON1,SSPEN;T Re-enable MSSP goto set_cf_error;T configuration error return ;****************************************************************************** HWSPI_W_speed ;On Entry:WREG = speedDATA & checks SSPCON1-3 for SPI mode ; speedDATA = 0x00 => Fosc/4 ; speedDATA = 0x01 => Fosc/16 ; speedDATA = 0x02 => Fosc/64 ; speedDATA = 0x03 => Timer Divisor (Not working yet) ; ;On Exit: ;On Success: return with C flag clear ;On Failure: return with C flag set ; bcfSSPCON1,SSPEN ;T Disable MSSP movwf speedLbyte;T move speedDATA stored in W to speedLbyte btfscSSPCON1,SSPM3 ;T In SPI Mode?, skip if yes call HWSPI_init;T MSSP is in wrong mode, Init for SPI ; ;Test if speedLbyte = 0x00. If yes, SPI clock speed = Fosc/4 movlw0x00;T load 0x00 into W subwfspeedLbyte,W;T subtract 0x00 from tcount result in w btfssSTATUS,Z;T test zero flag, skip next instr if z set gotofdiv16;T goto Fosc/16 section bcfSSPCON1,SSPM1;T SSPCON1-1 = 0 bcfSSPCON1,SSPM0;T SSPCON1-0 = 0 goto okjump3;T Fosc/4 was selected ;Test if speedLbyte = 0x01. If yes, SPI clock speed = Fosc/16 fdiv16movlw0x01;T load 0x01 into W subwfspeedLbyte,W;T subtract 0x01 from tcount result in w btfssSTATUS,Z;T test zero flag, skip next instr if z set gotofdiv64;T goto Fosc/64 section bcfSSPCON1,SSPM1;T SSPCON1-1 = 0 bsfSSPCON1,SSPM0;T SSPCON1-0 = 1 goto okjump3;T Fosc/16 was selected ;Test if speedLbyte = 0x02. If yes, SPI clock speed = Fosc/64 fdiv64movlw0x02;T load 0x02 into W subwfspeedLbyte,W;T subtract 0x02 from tcount result in w btfssSTATUS,Z;T test zero flag, skip next instr if z set gototimer;T goto Timer section bsfSSPCON1,SSPM1;T SSPCON1-1 = 1 bcfSSPCON1,SSPM0;T SSPCON1-0 = 0 goto okjump3;T Fosc/64 was selected ;Test if speedLbyte >= 0x03. If yes, SPI clock speed will be set by the timer ;SETTING THE SPI CLOCK WITH THE TIMER WILL RETURN A FAILURE AT THIS TIME. ;Future To do: Implement the TIMER section timermovlw0x03;T load 0x02 into W subwfspeedLbyte,W;T subtract 0x02 from tcount result in w btfssSTATUS,Z;T test zero flag, skip next instr if z set gotobadjmp2;T goto error section to return failure gotobadjmp2;T goto error section to return failure ;bsfSSPCON1,SSPM1;T SSPCON1-1 = 1 ;bsfSSPCON1,SSPM0;T SSPCON1-0 = 1 ;goto okjump3;T Fosc/64 was selected okjump3bsfSSPCON1,SSPEN;T Re-enable MSSP bcfSTATUS,C;T clear c flag on success return badjmp2bsfSSPCON1,SSPEN;T Re-enable MSSP bsfSTATUS,C;T set c flag on failure return ;****************************************************************************** HWSPI_W_spidata_W ;Simultaneously write SPI data on MOSI and read SPI data on MISO ; ;on Entry:WREG = mosiDATA & checks bit3 of SSPCON1 for SPI mode ;On Exit:WREG = misoDATA ;On Success: return with C flag clear ;On Failure: return with C flag set ; movwf temp2;T move mosiDATA stored in W to WREG_TEMP btfscSSPCON1,SSPM3 ;T In SPI Mode?, skip if yes call HWSPI_init;T MSSP is in wrong mode, Init for SPI movftemp2,W;T load W with original mosiDATA ; movwfSSPBUF;T move byte to transmit to SSPBUF (transmit buffer) movlw0x00;T load 0x00 into W movwftcount;T initialize tcount to zero (0x00) again1btfscSSPSTAT,BF;T receive completed? if no, skip next gotookjump1;T no. goto again incf tcount,F;T increment tcount movlw0xFF;T load w with literal subwftcount,W;T subtract 0xFF from tcount result in w btfssSTATUS,Z;T test zero flag, skip next instr if z set goto again1 ;T loop until timeout goto set_cf_error;T receive timeout error return okjump1 movf SSPBUF,W;T put received data in W gotoclear_cf_ok return ;****************************************************************************** ; UART routine asyxmtc bcfPORTC,xmit ;T used to be portc,xmit callfull movlw0x08 ;TEST_T "08" movwfbitctr asyxmt1 rrcf xmtreg,f btfsc STATUS,C goto asyxmt2 bcf PORTC,xmit ;T used to be portc,xmit goto asyxmt3 asyxmt2 bsf PORTC,xmit ;T used to be portc,xmit ; asyxmt3 callfull decfsz bitctr,f goto asyxmt1 ; bsf PORTC,xmit ;T used to be portc,xmit callfull retlw0 ;****************************************************************************** ; UART baud rate of 115.2kbps using a 40MHz System Clock full movlwd'3' movwfcntrb vdly0 movlwd'6' ; d'43' with 4MHz => 2400 baud movwfcntra vdly1 decfsz cntra,f goto vdly1 decfsz cntrb,f goto vdly0 retlw0 ;****************************************************************************** ;End of program END 表1. 配置写命令，将所有四路DAC的建立时间设置为3µs SPI Line C7 C6 C5 C4 C3 C2 C1 C0 D7 D6 D5 D4 D3 D2 D1 D0 DIN 1 1 1 0 1 1 0 0 0 0 0 0 1 1 1 1 表2. 装载全部DAC输出命令 SPI Line C3 C2 C1 C0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 DIN (1st) 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 DIN (2nd) 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 表2中，第一个命令将所有DAC输出设置为零，第二个命令将所有DAC设置为满量程输出。 相关型号   APP 3497: Jun 20, 2005 MAX5581 带缓冲、快速建立、四通道、12/10/8位、电压输出DAC 完整的数据资料 (PDF, 868kB) 免费样品 MAX5582 带缓冲、快速建立、四通道、12/10/8位、电压输出DAC 完整的数据资料 (PDF, 868kB) 免费样品 MAX5583 带缓冲、快速建立、四通道、12/10/8位、电压输出DAC 完整的数据资料 (PDF, 868kB) 免费样品 MAX5584 带缓冲、快速建立、四通道、12/10/8位、电压输出DAC 完整的数据资料 (PDF, 868kB) 免费样品 MAX5585 带缓冲、快速建立、四通道、12/10/8位、电压输出DAC 完整的数据资料 (PDF, 868kB) 免费样品 自动更新 需要自动接收最新发布的应用笔记吗？请订阅EE-Mail™ (English only)。 我们期待您的反馈！ 喜欢？不喜欢？有待改善？或为我们提供建议？请与我们联系 — 我们将根据您的意见或建议改善我们的工作。 网页评价或提供建议   下载，PDF格式 (84kB)  AN3497, AN 3497, APP3497, Appnote3497, Appnote 3497